Romco e-Catalogue 2019

30 Grab Bars 90° 30" x 30" L 1¼" Dia. B-5898 Satin B-5898.99 Peened Concealed Mounting with Snap Flange: • Constructed of 18-gauge, Type-304 satin-finish stainless steel tubing in 1¼" and 1½" diameter. • Concealed mounting flange  1 ⁄ 8 " thick, Type-304 stainless steel plate, 2" W, 3 1 ⁄ 8 " H, with screw holes for concealed anchors. • Cover is 22-gauge, Type-304 stainless steel with satin finish, 3 ¼" diameter. • Cover snaps over mounting flange to conceal screws. • Peened nonslip gripping surface available. Add suffix .99 to model number. Configurations, Dimensions, Finishes: 1½˝ Dia. Straight/Satin B - 6806x12 ˝ B - 6806x18 ˝ B - 6806x24 ˝ B - 6806x30 ˝ B - 6806x36 ˝ B - 6806x42 ˝ B - 6806x48 ˝ 1½˝ Dia. Straight/Peened B -6806.99x12 ˝ q B -6806.99x18 ˝ q B -6806.99x24 ˝ q B -6806.99x30 ˝ q B -6806.99x36 ˝ q B -6806.99x42 ˝ B -6806.99x48 ˝ 1 1 ⁄ 4 ˝ Dia. Straight/Satin B -5806x18 ˝ B -5806x24 ˝ B -5806x30 ˝ B -5806x36 ˝ B -5806x42 ˝ B -5806x48 ˝ 1 1 ⁄ 4 ˝ Dia. Straight/Peened q B -5806.99x18 ˝ q B -5806.99x24 ˝ q B -5806.99x30 ˝ q B -5806.99x36 ˝ q B -5806.99x42 ˝ B -5806.99x48 ˝ 251-4 WingIt ™ Grab Bar Fastener For 2½" and 3 ½" or deeper hollow walls with finished wall surfaces 1 ⁄ 4 " to 1½" thick. One fastener required for each flange. Corrosion-resistant stainless steel. Install grab bars without backing. The fastener will support 300 lbs load. WingIt ™ is a trademark of WingIt Innovations, LLC. Optional Mounting Kits: Order one per flange. Part No. 252-30 sheet-metal screws. Optional Anchor Devices: Order one per flange. Part No. 2583 anchors for 3 ⁄ 4 " to 1" panels; 2586 anchors for ½" panels. SERIES DIAMETER FINISH B-6806 1½" Satin Finish B-5806 1  1 ⁄ 4 " Satin Finish 90° 30 " x 30" L 1½" Dia. B-6898.99 Peened Snap Flange: • New 6-Hole Flange • Improves Installation Flexibility Improved New SAFETY WARNING : Grab bars are no stronger than the anchors and walls to which they are attached and, therefore, must be firmly secured in order to support the loads for which they are intended. To avoid potential injury, the building owner or maintenance personal should remove the grab bar from service if the grab bar is not adequately secured to wall or if there is any observed damage to welds.